How do I connect my 808 thump?

To connect your 808 thump, you’ll need to connect the USB cable that comes with the device to your computer or laptop. Once the device is connected, you’ll need to install the audio driver that comes with the device as instructed.

After you have successfully installed it, you’ll need to make sure the device is setup properly in your audio/MIDI preferences of your chosen DAW. The 808 thump is class-compliant, so you do not need any additional drivers.

Lastly, make sure you turn the volume knob on the device up to hear the sound playing from your computer.

Why is my wireless speaker not working?

There could be several reasons why your wireless speaker is not working. It is possible that there is a technical issue with the device itself. The speaker may not be connected correctly to a power source or it could be out of power and needs to be charged.

It could also be that the speaker is not within range of the Bluetooth connection and needs to be re-paired. Additionally, the sound receiver (computer, phone, etc. ) may not be outputting the correct audio signal and needs to be configured properly.

Finally, it might be that the speaker has malfunctioned and needs to be replaced. To determine the issue, try troubleshooting the speaker, power source, Bluetooth connection, and receiver in order to isolate the problem and find the solution.

How do you reset a wireless speaker?

Resetting a wireless speaker can vary depending on the make and model of the speaker and whether it is compatible with your device. Generally, the steps are similar and involve a few key pieces: locating the Reset button, holding it down for a few seconds and physically unplugging the power source.

To begin, locate the Reset button on your wireless speaker. This can typically be found on the back or bottom of the speaker, and it is often labeled with the word ‘Reset’ or a symbol that looks like a tiny hole.

Once the Reset button has been located, press and hold it down for 5-10 seconds. This will reset the speaker’s settings and should restore the connection.

Finally, unplug the power source, wait a few seconds and plug it back in. This should complete the reset process and restore the connection between your device and the speaker.

If you are having difficulty connecting the speaker to your device after the reset has been completed, it is recommended that you consult the product manual or contact the manufacturer directly for further assistance.

Why is there no sound coming from my Bluetooth speaker?

Firstly, check to make sure it is sufficiently charged. If it is, then make sure that the volume on the device you are trying to play audio from (e. g. a phone, a laptop, a tablet, etc. ) is set at an audible volume level.

Also, check that the audio connections are properly connected on both the device and the Bluetooth speaker. If those are all set correctly, then see if the Bluetooth device is connected and enabled on the device you are trying to play audio from.

Additionally, try turning the device and the Bluetooth speaker off and back on to confirm there are no technical issues with either. Lastly, make sure that the Bluetooth speaker is fully and properly unpaired from the list of devices in the Bluetooth settings of the device you are attempting to play audio from.

If none of these troubleshooting steps work, then it might be necessary to reset the Bluetooth speaker and re-pair it with the device.

Why is my Bluetooth connected but not playing?

Firstly, there may be a compatibility issue between your Bluetooth device and the one you’re trying to connect it to. Make sure both the device and your Bluetooth speaker/headphones are up to date with the latest version of their software and that they are compatible with each other.

Secondly, some Bluetooth connections may suffer from signal interference. Make sure to move away from any large electrical items, such as appliances, or move to another room in your home. This can help to clear up signal interference and get your Bluetooth connection working again.

Finally, sometimes a Bluetooth connection can be blocked. Make sure your device is not preventing other Bluetooth connections from playing, as some settings may be blocking connections. If in doubt, try restarting your device and see if that helps.

If all else fails, try reaching out to your device’s manufacturer for more help.

Why wont my speaker play music?

There are several potential reasons why your speaker won’t play music. The most common are:

1. A lack of power (ensure the speaker is correctly plugged in).

2. A malfunctioning or incorrect set-up of the Bluetooth or other connection (troubleshoot connection settings).

3. Faulty cables or ports (this could require a replacement, depending on the kind of speaker).

4. A defective speaker (this could require service).

You may also want to check the volume settings, as well as the type of audio device and media you’re using (some speakers may not support certain formats). It’s also possible that the speaker is simply too old or outdated to work properly.

It’s important to do some basic troubleshooting for hardware or incorrect settings before assuming the speaker is broken.

Why is my iPhone connected to Bluetooth speaker but no sound?

The most common issues are that the Bluetooth connection between the iPhone and speaker is not strong enough, the audio source (e. g. music app) is not playing, or the speaker itself is not properly set up.

To address any potential connection issues between the iPhone and the Bluetooth speaker, make sure that the Bluetooth connection is turned on for both devices and that the two devices are within range of each other.

Additionally, try turning off and on both the iPhone and the speaker to reset the connection and then reconnect them.

If the Bluetooth connection is working, then make sure the audio source, such as the music app, is playing. Also, check to see if the volume is set too low or if the speaker itself is muted. If none of those things work, then check the speaker setup within the iPhone settings to make sure that it is set up correctly and compatible with the speaker.

If you are still having trouble with getting sound from your Bluetooth speaker, then try using a different audio source, such as a different music app or YouTube. Additionally, consider resetting the speaker and re-pairing it to the iPhone or try connecting it to another device, such as a laptop, to see if that works.

How do you fix a Bluetooth speaker that won’t connect?

If your Bluetooth speaker won’t connect, the first step is to check the manufacturer’s website for any firmware or software updates that may be available for the product. If there are any updates available, download and install them according to the instructions.

If no updates are available, ensure that the speaker is sufficiently charged and that the Bluetooth connection on your device is activated. If your device has not been paired with the speaker before, search for the speaker in the Bluetooth settings of the device and follow the instructions to pair them.

If you have already paired the devices, try unpairing and repairing them in case the connection was interrupted or lost. To do this, go to your device’s Bluetooth settings, select the speaker, and select “unpair”.

Then, search for the speaker again, select it, and follow the instructions to pair them again.

Another possible issue is that your device does not support the speaker’s audio standard or the speaker’s audio output. If this is the case, change the audio standard or output setting of the speaker.

Finally, if none of the above steps work, try restarting both the speaker and your device. This will help to reset the connection and can sometimes help to fix the issue.

Why are my headphones connected but no sound?

The first possibility to consider is if the headphones are connected to the correct output, such as the headphone jack or optical audio out port. If they are, then the next thing to look at is the sound or audio settings in your device’s operating system.

In most cases, there are settings that allow you to adjust the audio settings, such as balance and volume. If these settings are not adjusted appropriately, then the headphones themselves will be receiving no signal.

It is also possible that the headphones themselves could be the source of the problem. This could be due to a loose connection, a worn out wire or drivers, or any other technical issue that could be preventing the sound to come through.

To test this, try connecting the headphones to another audio device or trying a different set of headphones.

Finally, if you’re using wireless headphones, it is possible that the connection has been interrupted. This could be from low batteries, interference from other wireless devices, or simply the headset being out of range.

In this case, check the battery level, reset the connection and try getting closer to the audio device.

If none of these solutions fix the problem, then it may be best to contact the manufacturer of the headphones or audio device for more technical support.

Why is my phone not playing audio?

There could be a few explanations as to why your phone is not playing audio. The first issue could possibly be related to a setting on your device. Depending on your device, see if the volume settings are turned up.

Make sure that the Do Not Disturb (DND) mode is turned off, and that your phone isn’t on ‘Silent’ mode as this can also prevent sound from playing. If the volume settings seem to be in order but you are still not hearing any sound, try plugging in a set of headphones and see if audio plays through them.

If the audio does play through the headphones, it’s possible that the speakers on your phone may have stopped working.

Another common issue is that the audio file you are trying to play may be corrupt or out of date. To check, try playing a different audio file and see if it plays. If not, try rebooting your device to clear any errors or temporary problems.

Lastly, it could be a problem with the app or program that you are using to play audio. If you’re using an app such as Spotify, check to make sure that the app is up to date. If it’s an older version, update it and see if the audio plays.

If none of the above works, it’s a good idea to try reinstalling the app or program, or even resetting your device to the original factory settings.

Why are my Bluetooth headphones connected but sound is coming from speakers?

It sounds like your Bluetooth headphones are connected to your device, but the audio isn’t being sent to the headphones. This could be due to a few things:

– Your device’s audio settings may not be configured properly. Make sure that the output device is set to your Bluetooth headphones in the audio settings menu of your device.

– The headphones may need to be reconnected. Disconnect the headphones from your device by turning off Bluetooth in your device’s settings. Then, turn Bluetooth back on and reconnect the headphones to your device.

– There may be an issue with the cables or the connection between the headphones and the audio device. If this is the case, you may need to reset the connection. Disconnect the headphones from your device, then reconnect them.

– Your speakers may be set as the device’s default output. Check to make sure this isn’t the issue. Look for an icon of headphones in your audio settings menu, and make sure it is checked to set your Bluetooth headphones as the primary audio output device.

– If you are using a headset with a microphones, make sure that the correct output device is selected. This can be done in the audio settings menu, and you should make sure that the microphone is selected as well.

If none of these steps work, then you may need to replace your headphones or contact their customer support.

What kind of speaker is 808?

808 is a reference subwoofer speaker, designed to provide huge, deep bass tones and impact. It is a popular choice among EDM and hip hop producers, who predominantly use 808’s for their sample-based tracks.

The 808 is famous for its distinct low-end thump sound, which is created by its unique cone-shaped design. It delivers a tight bass punch with a smooth, crisp sound. It also features an adjustable subwoofer control, allowing you to adjust the bass response.

The 808 is a great tool for achieving clean, punchy bass tones in any type of music.

How do kick and 808 work together?

Kick and 808 drums work together to create a strong rhythmic foundation for a track. They both provide low-end frequency sounds and can be used as the main beat in a track. The kick drum is typically used as the backbone and foundation of the track while the 808 provides a lower frequency sound that adds to the overall beat and pulse of the track.

The combination of kick and 808 drums is often used in hip hop, trap, and EDM genres, as well as other popular music styles. Generally, the 808 provides a low-frequency rumble while the kick provides a punchier sound.

Together they create a thick layer of low end that makes the track feel powerful and energetic. Experimenting with different kick and 808 sounds and techniques can help to create unique and interesting rhythms in your music.

How do I add 808 to garage band?

Adding the Roland TR-808 drum machine to your GarageBand project is quite simple. First, open up the AudioBrowser and select Drum Machine Designer. Here you will have a selection of drum machines to pick from.

Under the Sounds Library, click on the TR-808 Classic folder and drag it into your GarageBand project.

You can also adjust the tone and sound of the 808 inside of GarageBand. To do this, select the Drum Machine Designer and open up the Visual Editor. Here, you will be able to pick different sounds, and adjust the accent, decay, attack, and other parameters to customize the tone of the 808.

You can also add effects such as reverb or delay for even more sonic versatility.

Once you have finished making your adjustments, you can press the Play button or simply drag that track into the timeline. It is also possible to midi map a keyboard or other midi controller to the drum machine in GarageBand, so you can record some real-time 808 action.

How do you use 808 in logic?

Using 808s in Logic is a great way to add deep, thumping pitched percussion to your productions. In order to do this, you’ll need to have a basic understanding of the bass drum sub-sections so you can adjust them to your liking.

First, head to the library tab in your Logic project and select the “Drums” folder. You should find the default 808 kit, with each of its bass drum variations in there. Select one of these samples to begin with.

To adjust the parameters, open up the mixer tab, select the 808 channel and access the channel strip view. You’ll be able to fine-tune your 808 kick levels, as well as add effects such as reverb and saturation.

Next, select the pads tab in your Logic project, select the 808 kit and adjust the parameters to make the kick sound you want. Your options here will be much the same as before, with a few extra options such as tone and pitch.

Once you’ve finished adjusting your 808, you can start programming and sequencing it into your track. A common way to do this is to create a midi pattern and assign it to the 808 channel. This way, you can edit each setting and create a unique pattern to fit your track.

Lastly, you can use automation to add further depth to your 808. You can use this to change the parameters of your kick over time, such as the compression level or the amount of reverb applied to it.

This will give your 808 performance a much more dynamic and interesting approach.

Overall, Logic has a great range of 808 samples and a great set of tools to customize them to your liking. So have fun exploring the possibilities and creating unique 808 sounds for your projects.

Categories FAQ

Leave a Comment