How do I program my Remote Control to DIRECTV?

To program your remote control to DIRECTV first turn on your receiver. On the remote, press and hold the “Mute” and “Select” buttons at the same time. The green light at the top of the remote will blink twice, indicating it is ready to program.

Enter the code 922 on the keypad and press the “Select” button again. The green light will blink twice again and your remote is now programmed to your receiver.

To program your remote to control your TV, press the “TV” button at the top and enter the code for your TV. Refer to the user manual for your particular television model for the proper code. When you have entered the code press the “Select” button again and the green light will blink twice.

If you want your remote to control any other devices, press and hold the “Mute” and “Select” buttons at the same time, enter the four-digit code for that device and press the “Select” button again and the green light will blink twice to indicate the code was accepted.

Now you have programmed your remote control to DIRECTV and all your devices. Enjoy using your remote control!

How do I pair my remote to DirecTV?

To pair your remote to DirecTV, you will need an infrared (IR) or Universal remote. Once you have the correct remote, you will need to follow the steps below:

1. Locate the “Mode” button near the top of the remote and press it until the LED light flashes twice.

2. Press the “Mute” and “Enter” buttons at the same time, then release both.

3. Point the remote at the face of your DirecTV receiver. Make sure you keep it in line of sight, and hold the remote approximately 3 to 6 inches away.

4. Press the “Power” button and then release. The LED light should flash again.

5. Aim the remote at the DirecTV receiver again and press the “Ch Up” button. Release when the LED light flashes twice. This confirms your remote is successfully paired with your DirecTV receiver.

Your remote should now be paired with your DirecTV receiver. If you need additional help or support, please contact DirecTV directly.

What is the code for DirecTV remote?

Depending on the model of your DIRECTV remote, the code will vary. The code for some common remote models are as follows:

SAT-A65: 076

SAT-RC66RB (4 component): 081

RC23/RC23A: 050

RC24/RC24A/RC24B: 051

RC32/RC32A/RC32R: 052

RC64/RC64R/RC64RB: 053

RC66/RC66X/RC66RX: 054

RC71/RC72: 060

RC73: 068

RCLotus: 055

In order to find the code for your remote, go to the official DIRECTV site, search and click on your model, and the code should be listed.

Why won’t my DirecTV remote connect?

If your DirecTV remote is not connecting, you may have to try a few different troubleshooting methods to resolve the issue. Make sure that the batteries are fresh, that they are correctly inserted, and/or replace if needed.

Also ensure that the remote is correctly paired to your DirecTV receiver. To do this, turn on both the receiver and the TV, and then press and hold down the MUTE and SELECT keys at the same time until the green light at the top of the remote flashes twice.

If the pairing is successful, the green light will flash twice again. If the pairing is unsuccessful, try turning the components off for a few seconds and then repeating the process.

If that does not work, you can reset the remote. To reset the remote, press and hold down the MUTE and SELECT keys at the same time until the green light at the top of the remote flashes three times.

Then hold down the MUTE and SELECT keys for about 10 seconds until the green light at the top of the remote flashes four times. Once the reset is complete, press and hold the MUTE and SELECT keys at the same time until the green light at the top of the remote flashes twice.

If the issue persists, it could be a receiver issue. You can also access DirecTV’s Troubleshooting section if you’re having connection issues. If needed, you can reach out to DirecTV’s customer service for further troubleshooting assistance or a replacement remote.

How do I program my DirecTV remote without a code?

If you want to program your DirecTV remote without using a code, there are a few different ways you can go about it. The simplest approach is to use the “AUX” button on your remote to program a device like your TV or Blu-ray player.

To do this, press and hold the “AUX” button until the LED light flashes twice. Then, enter the code 0060, or whatever code is appropriate for your device, followed by the power button. If the code is successful, the LED will turn green and your device should be ready to use.

Another option is to use the “Find it Now” feature on the remote. To do this, press and hold the “Menu” button for 3 seconds until the on-screen menu appears. Then, select “Settings” and “System Setup” and scroll down to “Find it Now”.

Select this option and follow the on-screen instructions to program your device manually. You may need to select the manufacturer’s name and model number, as well as the device type before you can program it.

Finally, you can use the DirecTV Remote App to program your remote. This app is available for both iOS and Android devices and allows you to program your devices directly from your phone. To use the app, download it from the App Store or Google Play and sign in with your DirecTV account credentials.

Then, follow the on-screen instructions to easily get your remote set up.

Why is my remote not connecting?

First, make sure the batteries in your remote are fresh and properly installed. Second, make sure you are pointing the remote at the device you are trying to control. Lastly, make sure the remote is programmed correctly.

If the remote came with your device, consult your device manual to ensure the remote is programmed correctly. Additionally, ensure any components such as wires and power supplies are properly connected and the devices are powered on.

If the above steps do not work, the remote may be damaged or require updating. If that is the case, contact the manufacturer for more assistance.

How do I refresh my directv remote to my receiver?

To refresh your DIRECTV remote to your receiver, you will need to connect your remote to the receiver. You can do this by pressing MENU on the remote then Select Settings & Help. From there, select Settings then Remote Control.

On this menu, choose the “Program Remote” option, and then select the type of remote you are using (branded, universal, or Genie). Once the type is selected you can then press the SELECT button on the remote that is connected to the receiver.

You will now be asked to select the type of television you have (branded or universal) and then press the SELECT button again. On the next screen, you will see the option to “Test Remote” and press SELECT one last time.

If successful, the remote should now be connected to the receiver.

Why is my DirecTV remote not changing the channel?

If your DirecTV remote isn’t changing the channel, there could be a few potential reasons.

First, check the battery condition of your remote and replace if necessary. Press the ‘Mute’ and ‘Select’ button simultaneously for 3 seconds and if the green light flashes twice then the batteries are fine.

Another potential cause could be that the remote you are using is not automatically synced up with the DirecTV box. Try unplugging your DirecTV box for 30 seconds, then reconnect and power it on. Then wait 30 seconds, press and hold the ‘Mute’ and ‘Select’ buttons simultaneously, and a light should appear on the front of your box.

If the light is red, try syncing the remote once more.

If your remote still isn’t working, it’s time to connect with a DirecTV technician for additional support. Check if it’s an issue with your remote or an issue with the box itself.

What is the remote code for DIRECTV?

The remote code for DIRECTV depends on the type and model of your DIRECTV device. Each device has an exclusive code. To determine the remote code for your DIRECTV device, consult the following list of DIRECTV remote control codes, or use the DIRECTV remote code lookup tool on the DIRECTV website.

DIRECTV Remote Control Codes

• Thomson 150, 537 and 547

• Ortek/Pace 956

• Mitsubishi 650, 811 and 941

• Hughes 633 and 830

• RCA 611-2, 713 and 812

• Fisher 607

• Philips 604, 605, 607 and 626

• LG 739

• Memorex 591-2

• GE 599 and 600

• One-For-All 741

• Denon 612

• Xenith 580

• Hitachi 587 and 595

• InFocus 707

• Onkyo 736

• Pioneer 583 and 682

• Regal 609

If your DIRECTV device is not currently listed, you may require a universal remote control. Universal remote codes for DIRECTV are 3001, 3011, 3101 and 5001.

Can you program a universal remote to DIRECTV?

Yes, you can program a universal remote to DIRECTV. Depending on the type of universal remote you have, the programming instructions may vary. Generally, you can access the setup menu by pressing the “TV” button.

Then, select the “DirecTV” device type on the remote before you enter some keycodes that match the model of your DIRECTV receiver. Once you enter the keycodes, you will then be asked to select the type of remote you want.

You can then sync the remote by pointing it towards the DIRECTV receiver and pressing buttons on the remote. To verify the configuration, you can try some of the general commands such as “power” and “volume up/down”.

If these commands are working correctly, then the universal remote has been programmed correctly.

Why is my TV not responding to the remote directv?

There can be several reasons why your TV is not responding to the DIRECTV remote. First, make sure that the remote is properly paired with the receiver. To do this, remove the access card from the receiver and then reinsert it.

Another potential issue can be power-related. Unplugging the power cable from the receiver and then powering it back up can help to reset the unit and get it working again. If none of these solutions help, then it may be that the infrared sensor of your TV is either not properly set up or is not functioning.

In this case, you will need to follow the instructions of the TV manufacturer to ensure that the sensor is enabled and that the remote is working. Additionally, it may be the case that the batteries of the remote need to be replaced.

If the remote is still not working after replacing the batteries, then you may need to purchase a new remote from DIRECTV.

How can I control my DIRECTV without a remote?

If you don’t have access to a remote control for your DIRECTV device, there are still ways you can control it without the need for a physical remote.

Firstly, if you have a phone or tablet running either the Apple iOS or Google Android operating systems, you can download the DIRECTV app from the Apple App Store or Google Play Store. The app allows you to control your DIRECTV device using your phone or tablet.

If you have a DIRECTV+ Genie World Box, you can access its menu without a remote control. To do this, simply press and hold the power button on the front panel of your device for several seconds. This will bring up the menu.

You can also use a universal remote if you don’t have access to the DIRECTV remote. Most universal remotes are compatible with DIRECTV devices, so it’s worth taking a look at those to see if one will work with your device.

Lastly, many television models have the ability to control other devices through a feature called CEC (Consumer Electronics Control). This allows you to use the remote that came with your television to access the menu and change channels on your DIRECTV in much the same way a DIRECTV remote would.

Is the DIRECTV Genie remote universal?

No, the DIRECTV Genie remote is not universal. The Genie remote is designed to work exclusively with the DIRECTV Genie HD DVR and its related devices. It will not work with any other products, and it does not have the capability to control multiple devices at the same time.

However, DIRECTV does offer a universal remote for purchase that can control multiple devices, and it is compatible with DIRECTV-compatible TVs, receivers, and audio systems.

Can my Samsung TV remote control my cable box?

Yes, depending on which Samsung TV and which cable box you’re using, it is possible to use your Samsung TV remote to control your cable box. Modern Samsung Smart TVs include a “Universal Remote” feature that allows you to pair your Samsung TV with any other compatible device, including some cable boxes.

To set this up, you’ll need to press the Source Select button on your remote and scroll through until you find the appropriate cable box – often just labelled CBL/SAT or something similar. Once your Samsung TV has identified the cable box, follow the on-screen instructions to complete the setup and pair your cable box with your Samsung TV.

If your Samsung TV does not have the Universal Remote feature, you can use your Samsung remote for some basic functions, such as changing channels, adjusting the volume, and powering the cable box on and off.

Unfortunately, more advanced functions such as recording shows and navigating the onscreen guide may only be accessible with the cable box’s own remote.

Can I use my Samsung remote as a Universal Remote?

Unfortunately, no, you cannot use your Samsung remote as a universal remote. Universal remotes are typically programmed to work with a range of different devices, from different brands, from TVs and sound systems to DVD players and streaming devices.

Your Samsung remote is only programmed to work with Samsung televisions and devices, so it will not be compatible with other brands of electronics. If you want to use a single remote to control multiple devices, you may want to look into purchasing a universal remote.

Categories FAQ

Leave a Comment